Introduction

Introduction

The RF and Microwave Circuit Design for 5G/6G Training Course offers cutting-edge knowledge and practical experience in designing next-generation wireless communication systems. As the demand for high-frequency, high-speed, and high-bandwidth communication accelerates with the rise of 5G and 6G technologies, engineers must be equipped with the skills to create RF and microwave circuits that meet stringent requirements for low latency, high data rates, and energy efficiency. Training Course on RF and Microwave Circuit Design for 5G/6Gprovides hands-on training in the design, simulation, and validation of RF front-end modules, power amplifiers, mixers, filters, oscillators, and antennas using industry-standard tools such as Keysight ADS, HFSS, and MATLAB RF Toolbox.

Participants will dive deep into advanced topics such as millimeter-wave circuit design, beamforming, antenna array integration, EM simulation, and nonlinear device modeling. Real-world case studies from 5G base stations, mmWave handsets, automotive radar, and satellite IoT systems are integrated throughout the course. Whether you're an experienced RF engineer or a new graduate entering the telecommunications industry, this training prepares you to design, test, and optimize RF components for the next wave of ultra-fast, ultra-reliable wireless networks.

Programme Curriculum

Training Course on RF and Microwave Circuit Design for 5G/6G

Introduction

Course duration

10 Days

Course Objectives

Understand RF and microwave fundamentals for 5G/6G networks.
Design and simulate RF front-end circuits using ADS and HFSS.
Implement millimeter-wave (mmWave) components for high-frequency applications.
Analyze signal propagation, S-parameters, and impedance matching.
Design efficient power amplifiers with linearization techniques.
Integrate high-gain antenna arrays and beamforming networks.
Model and simulate mixers, filters, and oscillators for RF chains.
Optimize circuits for low noise figure and high linearity.
Address challenges in PCB layout for RF and mmWave systems.
Perform EM simulations using full-wave solvers.
Design circuits for RF energy harvesting and IoT applications.
Validate hardware performance with real-world case studies.
Prepare for 6G evolution with THz and AI-integrated circuits.

Organizational Benefits

Future-proof your team with 5G/6G-ready RF design skills.
Accelerate time-to-market for wireless and IoT products.
Reduce design errors with advanced simulation and modeling.
Improve system performance through optimized RF circuits.
Enhance innovation in telecom, radar, and satellite domains.
Build in-house expertise in cutting-edge RF technologies.
Reduce dependency on external design consultants.
Improve product efficiency, bandwidth, and coverage.
Ensure regulatory compliance and EMI/EMC readiness.
Position your organization as a leader in next-gen wireless systems.

Target Participants

RF and Microwave Engineers
Telecommunications Engineers
Embedded System Designers
Wireless Hardware Developers
Antenna Designers and Systems Engineers
IoT and Satellite Communication Teams

Course Outline

Module 1: Introduction to RF and Microwave Engineering

Frequency spectrum and applications
Key parameters: gain, noise, linearity
RF front-end overview
Differences between 5G and 6G requirements
Case Study: RF system in 5G smartphones

Module 2: Transmission Lines and S-Parameters

Coaxial, microstrip, and CPW lines
Reflection and return loss
Smith chart analysis
Impedance matching networks
Case Study: PCB trace design for GHz frequencies

Module 3: High-Frequency PCB Design for RF Circuits

PCB materials and stackups
Parasitics and signal integrity
Grounding and shielding techniques
RF connectors and transitions
Case Study: mmWave module PCB layout

Module 4: RF Simulation and Modeling Tools

ADS and Microwave Office overview
Circuit simulation and tuning
EM modeling with HFSS
Parameter sweeps and optimization
Case Study: Simulating a 3.5 GHz LNA

Module 5: Amplifier Design and Linearity

LNA and HPA topologies
Power gain and efficiency
Biasing techniques
Stability and matching
Case Study: 28 GHz PA design

Module 6: Mixer and Frequency Converter Design

Types of mixers: passive and active
Conversion loss and isolation
LO drive requirements
Image rejection techniques
Case Study: Mixer in 5G RFIC

Module 7: RF Filters and Duplexers

BPF, LPF, HPF design techniques
Filter response and pole placement
Duplexer structure and requirements
Miniaturization strategies
Case Study: 3 GHz SAW filter design

Module 8: Oscillators and PLLs

Phase noise and frequency stability
VCO design and analysis
Loop filter design
Frequency synthesizers
Case Study: PLL in 5G transceiver

Module 9: Antenna Design and Beamforming

Patch, dipole, and array antennas
Gain, radiation pattern, bandwidth
Beamforming techniques
Array calibration and phasing
Case Study: 64-element beamforming array

Module 10: mmWave and 6G Circuit Design

mmWave challenges and techniques
Component packaging and interconnects
Thermal and mechanical concerns
Sub-THz circuit design concepts
Case Study: 77 GHz radar module

Module 11: Nonlinear RF Behavior and Harmonics

Intermodulation and spurious responses
IP3 and P1dB measurements
Envelope simulation
Distortion and linearization
Case Study: Doherty PA nonlinearity mitigation

Module 12: RF Energy Harvesting and Low-Power Design

Rectenna design
Impedance matching for energy harvesting
Power management and conversion
Applications in IoT and sensors
Case Study: RF-powered temperature sensor

Module 13: EM Simulation for RF Circuits

3D modeling and meshing
Field solvers and convergence
Coupling and radiation analysis
Validation with hardware
Case Study: Antenna EM simulation

Module 14: Thermal and Reliability Analysis

Power dissipation in RF devices
Heat sink and via strategies
Reliability over temperature cycles
Aging models for semiconductors
Case Study: PA reliability in outdoor base stations

Module 15: RF Testing and Measurement

Network analyzers and spectrum analyzers
Noise figure, SNR, gain, and VSWR
Over-the-air (OTA) measurements
Calibration and de-embedding
Case Study: Lab testing of 5G module

Training Methodology

This course employs a participatory and hands-on approach to ensure practical learning, including:

Interactive lectures and presentations.
Group discussions and brainstorming sessions.
Hands-on exercises using real-world datasets.
Role-playing and scenario-based simulations.
Analysis of case studies to bridge theory and practice.
Peer-to-peer learning and networking.
Expert-led Q&A sessions.
Continuous feedback and personalized guidance.

Register as a group from 3 participants for a Discount

Send us an email: info@fineskilltrainingcenter.org or call +254769199797

Certification

Upon successful completion of this training, participants will be issued with a globally- recognized certificate.

Tailor-Made Course

We also offer tailor-made courses based on your needs.

Key Notes

a. The participant must be conversant with English.

b. Upon completion of training the participant will be issued with an Authorized Training Certificate

c. Course duration is flexible and the contents can be modified to fit any number of days.

d. The course fee includes facilitation training materials, 2 coffee breaks, buffet lunch and A Certificate upon successful completion of Training.

e. One-year post-training support Consultation and Coaching provided after the course.

f. Payment should be done at least a week before commence of the training, to Fineskill Training Center account, as indicated in the invoice so as to enable us prepare better for you.

Skills & Software Covered

RF Design Microwave Circuits 5G/6G Electronics

Programme Fee

Duration: 10 Days

Method: Online or Physical

Online Price: $2,000

Physical Price: $3,000

Certification: Accredited Certificate

View Available Dates 📄 Download Course Outline (PDF)

Available Sessions

Location

Month

Year

Oct 19 2026

19 Oct — 30 Oct 2026

💻 Online / Virtual session

Online $2,000